inosakiInosakiinosaki

Contact Us
sales@365accountings.com   

DFS60B-S4PA10000 – Incremental encoders – SICK Encoders

USD $ 418.53

SKU: 1036720

Incremental encoders generate information about position, angle, and rotation counts. The resolution is defined in the number of lines or pulses per rotation, which the encoder transmits to the control unit for each rotation. The current position can be determined by the control unit by counting these pulses. A reference run can be necessary when switching on the machine.

Part Number: 1036720
Encoders Model: DFS60B-S4PA10000
OEM Spec Ref 

Performance

Pulses per revolution10,000 1)
Measuring step90° electric/pulses per revolution
Measuring step deviation at non binary number of lines± 0.01°
Error limits± 0.05°
  • 1) See maximum revolution range.

Interfaces

Communication interfaceIncremental
Communication Interface detailTTL / HTL
Factory settingFactory setting: output level TTL
Number of signal channels6-channel
Programmable/configurable
Initialization time32 ms 1)

30 ms

Output frequency≤ 600 kHz
Load current≤ 30 mA
Power consumption≤ 0.7 W (without load)
  • 1) With mechanical zero pulse width.

Electrical data

Connection typeMale connector, M23, 12-pin, radial
Supply voltage4.5 … 32 V
Reference signal, number1
Reference signal, position90°, electric, logically gated with A and B
Reverse polarity protection
Short-circuit protection of the outputs✔ 1) 2)
MTTFd: mean time to dangerous failure300 years (EN ISO 13849-1) 3)
  • 1) Programming TTL with ≥ 5.5 V: short-circuit opposite to another channel or GND permissable for maximum 30 s.
  • 2) Programming HTL or TTL with < 5.5 V: short-circuit opposite to another channel, US or GND permissable for maximum 30 s.
  • 3) This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40°C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532.

Mechanical data

Mechanical designSolid shaft, face mount flange
Shaft diameter10 mm
Shaft length19 mm
Weight+ 0.3 kg
Shaft materialStainless steel
Flange materialAluminum
Housing materialAluminum die cast
Start up torque0.5 Ncm (+20 °C)
Operating torque0.3 Ncm (+20 °C)
Permissible Load capacity of shaft80 N (radial)

40 N (axial)

Operating speed≤ 9,000 min⁻¹ 1)
Moment of inertia of the rotor6.2 gcm²
Bearing lifetime3.6 x 10^10 revolutions
Angular acceleration≤ 500,000 rad/s²
  • 1) Allow for self-heating of 3.3 K per 1,000 rpm when designing the operating temperature range.

Ambient data

EMCAccording to EN 61000-6-2 and EN 61000-6-3
Enclosure ratingIP67, Housing side, male connector (IEC 60529) 1)

IP65, shaft side (IEC 60529)

Permissible relative humidity90 % (Condensation not permitted)
Operating temperature range–40 °C … +100 °C 2)

–30 °C … +100 °C 3)

Storage temperature range–40 °C … +100 °C, without package
Resistance to shocks70 g, 6 ms (EN 60068-2-27)
Resistance to vibration30 g, 10 Hz … 2,000 Hz (EN 60068-2-6)
  • 1) With mating connector fitted.
  • 2) Stationary position of the cable.
  • 3) Flexible position of the cable.
Weight0.321 kg
Dimensions13.5 × 9 × 18 cm

Title

Go to Top