inosakiInosakiinosaki

Contact Us
sales@365accountings.com   

Omron EE-SY671 EE-SY672 Series – Photomicro Sensors- Diffuse-Reflective

USD $ 19.32USD $ 22.05

SKU: N/A

Omron produce industrial sensors range such as fiber sensors, photoelectric sensors, displacement sensors/ measurement sensors, proximity sensors, photomicro sensors and rotary encodes.

Features

• Easy adjustment with a built-in sensitivity adjuster.

• Easy optical axis monitoring with a bright light indicator.

• Compact design incorporating a built-in amplifier and special IC enables direct switching capacity of up to 100 mA.

• Wide operating voltage range: 5 to 24 VDC

• Connection possible with a range of ICs, relays, and Programmable Controllers (PLCs).

 

Lineup

Sensors

AppearanceSensing methodSensing distanceOutput typeOutput configurationModel
Horizontal type444_lu_1_1Reflective type1 to 5 mm
(Infrared light)
NPN outputDark-ON or Light-ON
(Selectable) *
EE-SY671
Vertical type444_lu_1_2EE-SY672
* The Dark-ON/Light-ON (selectable) models are normally used as dark-ON models. To use them as light-ON models, short-circuit the L terminal and positive (+) terminal.
An EE-1001-1 Connector with the terminals already short-circuited is also available.

 

Accessories (Order Separately)

TypeCable lengthModelRemarks
ConnectorConnectorEE-1001
EE-1001-1L terminal and positive (+) terminal are
already short-circuited.
EE-1009 *
Connector with Cable1 mEE-1006 1M
EE-1010 1M *
2 mEE-1006 2M
EE-1010 2M *
Connector with Robot Cable1 mEE-1010-R 1M *
2 mEE-1010-R 2M *
Connector Hold-down ClipEE-1006AApplicable Photomicrosensors
For EE-SY671 and 672 only.
(Can be used only with EE-1006
Connectors for the
Photomicrosensors listed above.)

Note: For details, refer to the Photomicro Sensors Accessories on EE-[] which can be accessed from your OMRON website.
* EE-1009- or EE-1010-series Connectors have a builtin locking mechanism to prevent cable disconnection when only the cable is pulled. To remove the Connector from the Sensor, grip the top and bottom of the Connector firmly and push into the Sensor once before pulling out. The locking mechanism prevents the Connector from being removed by pulling on the cable only and enables removal only when the Connector (housing) is pulled.

 

Specifications

ModelsEE-SY671, EE-SY672
Sensing distance1 to 5 mm (Reflection factor: 90%; white paper 15 × 15 mm)
Sensing objectTransparent or opaque: 15 × 15 mm min.
Differential distance0.5 max. (with a sensing distance of 3 mm, horizontally)
Light sourceGaAs infrared LED with a peak wavelength of 940 nm
Indicator *1Light indicator (red)
Supply voltage5 to 24 VDC ±10%, ripple (p-p): 10% max.
Current consumption40 mA max.
Control outputNPN open collector:
Load power supply voltage: 5 to 24 VDC
Load current: 100 mA max.
OFF current: 0.5 mA max.
100 mA load current with a residual voltage of 0.8 V max.
40 mA load current with a residual voltage of 0.4 V max.
Response frequency *250 Hz min. (Average: 500 Hz)
Ambient illumination *31,500 lx max. with fluorescent light on the surface of the receiver
Ambient temperature rangeOperating: – 25 to +55°C
Storage: – 30 to +80°C
Ambient humidity rangeOperating: 5% to 85%
Storage: 5% to 95%
Vibration resistanceDestruction: 20 to 2,000 Hz (peak acceleration: 100 m/s2)
1.5-mm double amplitude for 2 h (4-min periods) each in X, Y, and Z directions
Shock resistanceDestruction: 500m/s2 for 3 times each in X, Y, and Z directions
Degree of protectionIEC IP50
Connecting methodSpecial connector (direct soldering possible)
WeightApprox. 3.5 g (including screwdriver for adjustment)
MaterialCasePolybutylene phthalate (PBT)
Emitter/receiverPolycarbonate
AccessoriesScrewdriver for adjustment

*1. The indicator is a GaP red LED (peak wavelength: 690 nm).
*2. The response frequency was measured by detecting the following rotating disk.

 

EE-SY671 / 672 Specifications 2

*3. The ambient illuminance is measured on the surface of the receiver.

Title

Go to Top